Skip to content
Rize Bikes CanadaRize Bikes Canada
How to check battery fuse?

How to check battery fuse?

How To Check Battery Fuse?

How To Check Battery Fuse? If you own electric bikes, there’s a very good chance you have an LG battery attached to it.

This is because LG makes great batteries, and here at Rize Bikes, we have been retrofitting LG batteries to all of our electric bikes from day one.

That being said, there is a chance your LG battery could stop working and refuse to budge at some point way into the future.

So what do you do if your e-bike battery stops working? Well, there are a few simple things you can quickly test to get to the bottom of your battery issues.

In most cases, the issue will be merely a blown fuse, allowing you to replace the fuse and get your battery working in just a few minutes. Here’s how to do it:

What You Will Need

- Rize / LG e-bike battery.
- Rize / LG e-bike battery charger.
- Volt Amp Test Meter/voltmeter (your local hardware store will have these. They are also fairly inexpensive on Amazon).
- 30 amp fuse for output port or 5 amps fuse for input port (color doesn’t matter. These are also cheap on Amazon.)

Now that you have everything in the above list, you’re ready to get started.

Step 1: Test the charger

It might seem obvious, but the first thing you should do is check your charger for signs of life. Your charger light will typically display two colors, and both will help you when it comes to diagnosing the problem with your battery.

Plug in the charger into the battery and if the charger light is red, it means the battery is charging, and the battery input fuse working fine. If the charger light is green, it could mean one of three things:

A) The battery is already fully charged.

B) Something is wrong with the input fuse (5 amps), probably burned. 

C) The charger is defected.

Step 2: Check the battery’s voltage

You’ll need to use your voltmeter to determine if the battery is fully charged or working. To conduct a voltage test and ensure the output fuse is delivering power from the battery and working fine, turn the battery on its side, turn on the voltmeter to DCV or 200k ohms, depending on your voltmeter.

Then, locate the positive and negative terminals on your battery located at the upper side of the battery. Insert the positive and negative leads of the voltmeter into the dedicated terminals. If the volt test meter reads somewhere around 54 volts that means your battery is working.

If your voltmeter shows 0v, it is safe to assume that there is a problem with your output fuse, meaning the fuse is not delivering power from battery, and you will need to perform a fuse replacement.

Step 3: Examine the fuse

The next step is to take the fuse out of the battery to examine it.

Start by using a screwdriver to unscrew the four small screws to remove the battery cap.

You will either need to remove the bottom (input port) or top cap (output port) depending on which fuse you will need to examine.

Next, use your fingers to pinch the fuse and pull it out of the battery (like a loose tooth).

Note: it is completely normal to wiggle the fuse around a bit to get it out of the battery. Once the fuse is out, take a look at it. You might be able to see the fuse has broken or burned links.

You may also measure the continuity of fuse using the voltmeter. Simply turn the voltmeter to Continuity and place both leads on each side (prongs) of the fuse. If the fuse works, you will hear a beeping sound from the voltmeter.

Step 4: Replace the fuse

If your fuse does not work you will need to replace it. The input fuse requires 5 amps and the output fuse requires 30 amps.

Step 5: Check the battery’s voltage (again)

If you have replaced the output fuse, do another voltage test on the battery. This time, the voltmeter should read at around 54 volts, depending on how much power is left in the battery.

The important part is that now, the battery is showing voltage, which tells us that your battery is working fine.

Step 6: Check the battery’s charger (again)

If you have replaced the input fuse, test the charger. Plug in the charger into the battery and if the charger light is red, it means the battery is charging.

Step 7: Enjoy your Rize Bike!

Now that your burned fuse has been replaced and your battery is working again, you can return to using your electric bike.

Plus, now you know how to replace your own fuse, so the next time your bike battery appears not to be working, you can troubleshoot and repair it even faster!

It does not matter if you own a road e bike, electric fat bike, or a retro electric bike, the steps to check your battery fuse will remain the same. Once you master this skill, you will be an expert for years to come.

Watch this video for a step-by-step tutorial on how to do everything discussed in this blog post.

Replacing a broken fuse is a simple fix for a common e-bike battery issue.

There might be other reasons your electric bike battery is not working, requiring a different fix. We will continue to update the Rize blog with more tips and tricks to keep your e-bike working as it should, so please follow along.

Please also follow us on Instagram and Facebook. Thanks for reading!

Cart 0

Your cart is currently empty.

Start Shopping